F9F Panther Catapult Hook Up

The F9F Panther's catapult hook was retractable and located in the "notch" between the aft end of the speed brakes.

It can just be seen in this photo between the heads of the sailors hooking the pendant to it.

The holdback was attached to a retractable hook on the belly aft of the main landing gear.

Put it all together...

X-47B Nose Gear Door Logos

The two seals on the forward end of the door on the second line are "zaps" from two carriers that the X-47B flew from, Roosevelt and Bush. The remainder are company logos.

Air & Space FH-1 Phantom Pictures

 

Note belly tank attach points (red)

Note recess for JATO bottle attachment...

Piasecki HUP Interior

12 January 2026: For details on the landing gear: https://tailhooktopics.blogspot.com/2026/01/piasecki-hup-landing-gear.html

17 August 2026: Added Amodel review by Paul Boyer 

 The HUP was somewhat underpowered so an interior might be somewhat less well furnished than shown here:

The rescue hoist was mounted above the right front seat and the rescue hatch below it so it had to be removed or folded forward for hoist operations:

Note that the flight controls including the cyclic, as shown above, might remain in place but the seat could not be folded forward unless it was removed.

 However, the pilot and crewman had to be insure that the rescuee didn't grab the controls as he came into the cabin.

There were several instrument panel arrangements. The top one was BuNo 128503-128600.

The cabin interior ended at the attachment point for the aft main landing gear strut;

The engine was mounted aft of the hole in the bottom of the fuselage and backwards, so the drive shaft pointed aft and the engine exhaust stack was forward of the engine.

The engine was mounted at an angle and drove a gearbox that had outputs forward to the front rotor and upwards to the aft rotor.

The engine was encased in a shroud. There was a fan on the "front" of the engine that sucked air in from the openings in the front of the pylon for engine cooling. The air exhausted out the opening in the bottom of the fuselage. An oil cooler was mounted at the rear of the opening.

The above inboard profile was created before the second pair of air inlets was added to the leading edge of the pylon and it appears to have an early version of the trailing edge of the fin. (The second pair of air inlets was added to leading edge of the HUP's aft pylon after it first entered service in order to increase cooling air to its hard working radial engine mounted in the fuselage.) The opening looks like a rounded rectangle from the side but because of the airfoil shape of the pylon cross section and the pylon's interface with the fuselage, it looks very different when viewed from other angles.

As a result, some kits have gotten the shape of the opening wrong.

This fuselage stations drawing can't be strictly relied on for shape but the station dimensions should be accurate (the overall length of the "shadow" on the ground was 31' 11"):

 Or a bit less as shown on this three view;

Note the shape of the rotor blade on the three view above. There were three different rotor blades. The first type had a tapered rounded tip as shown on the three view. The second had a constant chord of 1' and the outboard section was slightly twisted leading edge down with no taper. The third may be the same the same as the second in overall shape but was all-metal rather than being a wood-covered steel tube.

As far as I know, the rotor diameter was 35' for all blades.

The HUP-3s were H-25s built under contract to the Army. Fifty were delivered to the Navy instead. The H-25s had a slightly different interior and a different rotor head; the Navy may have installed the HUP rotor heads at some point.

(My guess is that the difference was the need for droop stops to keep the rotor from flapping excessively during startups and shutdowns on an aircraft carrier making a relatively high wind over deck for airplane takeoffs and landings.)

Another difference was that some H-25s (51-16577 and 51-16584 and subsequent) had a fairing on the right side of the fuselage associated with the field litter installation ( seen here under the side number of HUP-3 BuNo 147602):

 

For an excellent in-box review of the Amodel 1/72 HUP kit, see http://alexsmodelling.blogspot.ru/2017/03/hup-retriever-amodel-kit-review.html

Gordon Hewstone built the Siga 1/72 UH-25B kit: "It's a relatively crude kit to which I added a few details such as the lights and wiring on the landing gear".

Paul Boyer built the Amodel kit: 

 "The kit is the disappointing AModel kit, probably repackaged from other manufacturers. I also had a Pavla vacuum-formed front “canopy”, but otherwise I used what was in the kit. The rotor heads are over-complicated and under detailed for the scale. I added counterweights at the top and that helps.

The paint is Mr. Color fluorescent red and engine gray. I’ve been holding onto some ALPS decals I think Norm Filer made for me probably 30 years ago! The white “ink” is pretty translucent, so I applied one over another over another - three layers - to look opaque on the Dayglo."

Early P2Vs

Some odds and ends on the differences between the P2V-3 and the P2V-7...

P2V-3 Gun Nose:

P2V-3 Gun Nose vs. P2V-7 forward fuselage:

P2V-3C forward fuselage (significant differences in red) versus P2V-7 (the P2V-7 nose looks a bit off):

Note that for the P2V-7, the bomb bay was bulged downward (a change introduced with the -5), the nose landing gear moved forward to accommodate a bigger radar on the belly, and the canopy raised and relocated forward.

P2V-7 Nose Turret

The P2V-5 nose turret may be similar but the -5 did not have the raised canopy or the forward nose wheel well. (The forward end of the -5 wheel well was at Sta 114, 25" aft of the -7's.)

P2V Tail Turret

Note the rotation of the unit that was introduced at some point early on as a 2° downward rotation of the aft fuselage beginning about half way between the leading edge of the vertical fin and the leading edge of the horizontal stabilizer (it also resulted in the tilting aft of the vertical fin).

What's Under the AD Skyraider Canopy?

I have wondered exactly what was behind the headrest of the AD Skyraider canopy. It looked like a tan canvas-like cover that angled down from the top of the headrest to the top of the fuselage just before the aft end of the canopy. And that's just what it appears to be.

The deck behind the headrest is actually the top of the fuselage. The canopy slides on three rails, one on each side of the cockpit and one on the top of the fuselage.

The sliding canopy was powered.

That mechanism appears to be the only hardware under the sliding canopy. Note the "boot" that enclosed the mechanism. It appears to have a closure at the top over the air-to-oil transfer cylinder.

Early Skyraiders did not have the boot.

It appears that it was added to ensure that a leak from the mechanism would not be sprayed into the cockpit enclosure. The boot was not always in place.

The armor plate and seat arrangement (note that the canopy actuation mechanism is not shown).

The headrest that was attached to the armor plate could be tilted forward. Some other pictures;

KittyHawk XF5U

Kitty Hawk has just released an unusual choice for a plastic model kit, the Vought XF5U-1, in 1/48 scale.

The prototype never actually flew, having been overtaken by jets while it was being designed and built. For a brief history on the program, see http://thanlont.blogspot.com/2012/07/missed-it-by-that-much.html

Here are a few notes on the configuration of the prototype that might be of interest in building the kit.

There are pictures of the prototype before markings were added to the vertical fin.

Some of the few pictures that exist are in a ground-run configuration. Although self-boarding steps were provided, a set of wooden steps were used for ease of accessibility to the cockpit and maintenance-access panels.

A closeup of the temporary and self-boarding steps.

These self-boarding steps are accurately represented on the kit parts based on this built model.

Note, however, that the direction of rotation of the propellers is incorrect on this model.

Handrails were provided for ground run.

The model pictured above doesn't show the prominent cowl flaps and the second set of flaps behind them but the actual kit appears to provide at least separate cowl flaps. (Note that the left-hand flap behind the cowl flap is missing in the following picture.)

This wind-tunnel model included both sets of flaps.

The cowl flaps were repeated on the bottom of the fuselage along with a third cooler outlet flap under the center of the "fuselage".

The tip of the nose was clear because it was intended that a gun camera and approach light be located there.

This drive-train illustration provides an indication as to the location of the coolers:

The tailhook mechanism depicted on the built model looks a little off to me. Here is a annotated diagram from the Vought maintenance instructions.

Note that the tailhook was not installed on the prototype.

Note the location of the steps and the position of the cooling flaps.

A closeup of the pitch and roll control surface (the flaps in the afterbody were for trim).

The best single reference for the XF5U is, as usual, from Steve Ginter.

It can be ordered directly from him: http://www.ginterbooks.com/NAVAL/NF21.htm